I forgot, when i ping on the internet it workd too. I happend to me before with Windows but i forgot what I did to make it works...
 
Thanks!
 
Mickael

The "lo" is just your local network interface, don't worry about this.
 
It seems that there is a problem;
 
eth0 Link encap:Ethernet HWaddr FF:FF:FF:FF:FF:FF
 
does not seem right. It should have a valid hardware address.
 
Is the D-link set up via USB port?
 
We have a real networking expert onboard. Hopefully he will see this post.

Hi!
 
I believe the 'Ethernet HWaddr FF:FF:FF:FF:FF:FF' is the mac address. I found the options where i can inform the mac address of the Ethernet Card but when i look in windows it doesn't tell me the mac at all! How can I discover that?
 
My Modem is connected to a hub, it has all the router options (with DHCP server), I putted all the firewalls options off, on the modem and in Linux. But still, I have no answers from the web except the package from the ping!
 
Got an idea?
 
Mickael

Quote:I believe the 'Ethernet HWaddr FF:FF:FF:FF:FF:FF' is the mac address.
can't be. sorry. all bits on is the ethernet broadcast address.

Until ifconfig shows the same MAC address as Windows, then you've
got some kind of configuration problem.


Quote:when i look in windows it doesn't tell me the mac at all! How can I discover that?

(assuming WinXP)
Start->Run-> "cmd" -> then "ipconfig /all"

You'll get full interface information, IP address and MAC address.


In linux, if you check the output of 'dmesg' or the contents
of /var/log/messages, does it say anything interesting about 'eth0'?

Hi!
 
Because I don't understand every line of that flood (sorry for the mess) I decide to put all the things that look like network hardware things. It's from the '/var/log/messages'.
 
Feb 12 05:05:17 localhost kernel: parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,EPP]
Feb 12 05:05:17 localhost kernel: parport0: irq 7 detected
Feb 12 05:05:17 localhost kernel: cs: IO port probe 0x0c00-0x0cff: clean.
Feb 12 05:05:17 localhost kernel: cs: IO port probe 0x0100-0x04ff: excluding 0x200-0x20f 0x378-0x37f 0x480-0x48f 0x4d0-0x4d7
Feb 12 05:05:17 localhost kernel: cs: IO port probe 0x0a00-0x0aff: clean.
Feb 12 05:05:17 localhost kernel: ip_tables: 2000-2002 Netfilter core team
Feb 12 05:05:17 localhost kernel: ip_tables: 2000-2002 Netfilter core team
Feb 12 05:05:17 localhost kernel: eth0: Media Link On 100mbps full-duplex
Feb 12 05:05:17 localhost kernel: i2c /dev entries driver
Feb 12 05:05:17 localhost kernel: parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,EPP]
Feb 12 05:05:17 localhost kernel: parport0: irq 7 detected
Feb 12 05:05:17 localhost kernel: lp0: using parport0 (polling).
Feb 12 05:05:17 localhost kernel: lp0: console ready
Feb 12 05:05:18 localhost cups: cupsd startup succeeded
Feb 12 05:05:18 localhost sshd: succeeded
Feb 12 05:05:18 localhost xinetd: xinetd startup succeeded
Feb 12 05:05:18 localhost nfs: Starting NFS services: succeeded
Feb 12 05:05:18 localhost nfs: rpc.rquotad startup succeeded
Feb 12 05:05:18 localhost xinetd[2632]: xinetd Version 2.3.13 started with libwrap loadavg options compiled in.
Feb 12 05:05:18 localhost xinetd[2632]: Started working: 0 available services
Feb 12 05:05:19 localhost kernel: Installing knfsd (copyright 1996 okir@monad.swb.de).
Feb 12 05:05:19 localhost nfs: rpc.nfsd startup succeeded
Feb 12 05:05:19 localhost nfs: rpc.mountd startup succeeded
Feb 12 05:05:19 localhost rpcidmapd: rpc.idmapd -SIGHUP succeeded
Feb 12 05:05:20 localhost sendmail: sendmail startup succeeded
Feb 12 05:05:20 localhost sendmail: sm-client startup succeeded
Feb 12 05:05:20 localhost gpm[2728]: *** info [startup.c(95)]:
Feb 12 05:05:20 localhost gpm[2728]: Started gpm successfully. Entered daemon mode.
Feb 12 05:05:20 localhost gpm[2728]: *** info [mice.c(1766)]:
Feb 12 05:05:20 localhost gpm[2728]: imps2: Auto-detected intellimouse PS/2
Feb 12 05:05:21 localhost gpm: gpm startup succeeded
Feb 12 05:05:21 localhost crond: crond startup succeeded
Feb 12 05:05:21 localhost xfs: xfs startup succeeded
Feb 12 05:05:22 localhost xfs[2764]: ignoring font path element /usr/X11R6/lib/X11/fonts/Speedo (unreadable)
Feb 12 05:05:22 localhost winbind: winbindd startup succeeded
Feb 12 05:05:23 localhost anacron: anacron startup succeeded
Feb 12 05:05:23 localhost atd: atd startup succeeded
Feb 12 05:05:23 localhost readahead: Starting background readahead:
Feb 12 05:05:23 localhost rc: Starting readahead: succeeded
Feb 12 05:05:23 localhost messagebus: messagebus startup succeeded
Feb 12 05:05:24 localhost cups-config-daemon: cups-config-daemon startup succeeded
Feb 12 05:05:24 localhost haldaemon: haldaemon startup succeeded
Feb 12 05:05:24 localhost sysctl: net.ipv4.ip_forward = 0
Feb 12 05:05:24 localhost sysctl: net.ipv4.conf.default.rp_filter = 1
Feb 12 05:05:24 localhost sysctl: net.ipv4.conf.default.accept_source_route = 0
Feb 12 05:05:24 localhost sysctl: kernel.sysrq = 0
Feb 12 05:05:24 localhost sysctl: kernel.core_uses_pid = 1
Feb 12 05:05:24 localhost NetworkManager: Setting network parameters: succeeded
Feb 12 05:05:24 localhost NetworkManager: starting...
Feb 12 05:05:25 localhost NetworkManager: RTNETLINK answers: File exists
Feb 12 05:05:25 localhost NetworkManager: NetworkManager startup succeeded
Feb 12 05:05:25 localhost fstab-sync[2868]: removed all generated mount points
Feb 12 05:05:26 localhost NetworkManager: AUTO: Best wired device = (null)
Feb 12 05:05:26 localhost NetworkManager: AUTO: Best wireless device = (null) (null)
Feb 12 05:05:26 localhost fstab-sync[2915]: added mount point /media/NO_NAME for /dev/sda1
Feb 12 05:05:28 localhost fstab-sync[2988]: added mount point /media/cdrecorder for /dev/hdc
Feb 12 05:05:32 localhost NetworkManager: nm_create_device_and_add_to_list(): adding device 'eth0' (wired)
Feb 12 05:05:33 localhost NetworkManager: AUTO: Best wired device = eth0
Feb 12 05:05:33 localhost NetworkManager: AUTO: Best wireless device = (null) (null)
Feb 12 05:05:33 localhost NetworkManager: SWITCH: best device changed
Feb 12 05:05:33 localhost NetworkManager: nm_state_modification_monitor(): beginning activation for device 'eth0'
Feb 12 05:05:33 localhost dhclient: sit0: unknown hardware address type 776
Feb 12 05:05:34 localhost dhclient: sit0: unknown hardware address type 776
Feb 12 05:05:37 localhost dhclient: DHCPREQUEST on eth0 to 255.255.255.255 port 67
Feb 12 05:05:37 localhost dhclient: DHCPACK from 192.168.0.1
Feb 12 05:05:37 localhost NET: /sbin/dhclient-script : updated /etc/resolv.conf
Feb 12 05:05:37 localhost dhclient: bound to 192.168.0.5 -- renewal in 1004867 seconds.
Feb 12 05:05:38 localhost NetworkManager: nm_state_modification_monitor() activated device eth0
Feb 12 05:05:40 localhost kernel: ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 10 (level, low) -> IRQ 10
 
--------------------------------------------------------
Here's also an error from the System log (at the boot) :
 
Feb 12 05:05:05 localhost kernel: Security Scaffold v1.0.0 initialized
Feb 12 05:05:05 localhost kernel: SELinux: Initializing.
Feb 12 05:05:05 localhost kernel: SELinux: Starting in permissive mode
Feb 12 05:05:05 localhost kernel: There is already a security framework initialized, register_security failed.
 
Feb 12 05:05:07 localhost kernel: vesafb: probe of vesafb0 failed with error -6
 
----------------------------------------------
And here's the parameters of the network card:
 
IPCONFIG (WINDOWS)
Suffixe DNS propre à la connexion :
Description . . . . . . . . . . . : Carte Fast Ethernet PCI de base SiS900
Adresse physique . . . . . . . . .: 00-00-00-00-00-00
DHCP activé. . . . . . . . . . . : Oui
Configuration automatique activée . . . . : Oui
Adresse IP. . . . . . . . . . . . : 192.168.0.4
Masque de sous-réseau . . . . . . : 255.255.255.0
Passerelle par défaut . . . . . . : 192.168.0.1
Serveur DHCP. . . . . . . . . . . : 192.168.0.1
Serveurs DNS . . . . . . . . . . : 192.168.0.1
Bail obtenu . . . . . . . . . . . : 11 février, 2005 15:41:01
Bail expirant . . . . . . . . . . : 13 mars, 2005 15:41:01
 
ROUTE (WINDOWS)
Itinéraires actifs :
Destination réseau Masque réseau Adr. passerelle Adr. interface Métrique
0.0.0.0 0.0.0.0 10.0.0.1 10.0.0.4 20
10.0.0.0 255.255.255.0 10.0.0.4 10.0.0.4 20
10.0.0.4 255.255.255.255 127.0.0.1 127.0.0.1 20
10.255.255.255 255.255.255.255 10.0.0.4 10.0.0.4 20
127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1
224.0.0.0 240.0.0.0 10.0.0.4 10.0.0.4 20
255.255.255.255 255.255.255.255 10.0.0.4 10.0.0.4 1
Passerelle par défaut : 10.0.0.1
 
IFCONFIG (LINUX)
eth0 Link encap:Ethernet HWaddr FF:FF:FF:FF:FF:FF
inet addr:192.168.0.5 Bcast:192.168.0.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:139 errors:0 dropped:0 overruns:0 frame:0
TX packets:154 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:18197 (17.7 KiB) TX bytes:11053 (10.7 KiB)
Interrupt:9 Base address:0xe000
 
 
 
ROUTE (LINUX)
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
192.168.0.0 * 255.255.255.0 U 0 0 0 eth0
default 192.168.0.1 0.0.0.0 UG 0 0 0 eth0
 
 
Please tell me you know the problem!
 
 
Mickael

c'est étrange
 
I can't explain the MAC addresses being what they are (and -very- different)
in Windows and Linux.
 
The Windows route table, however, indicates the system IP address was 10.0.0.4
and the default gateway was 10.0.0.1
 
 

Sorry, I did some test at my friend's house... This is the real route table:
 
Itinéraires actifs :
Destination réseau Masque réseau Adr. passerelle Adr. interface Métrique
0.0.0.0 0.0.0.0 192.168.0.1 192.168.0.4 20
127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1
192.168.0.0 255.255.255.0 192.168.0.4 192.168.0.4 20
192.168.0.4 255.255.255.255 127.0.0.1 127.0.0.1 20
192.168.0.255 255.255.255.255 192.168.0.4 192.168.0.4 20
224.0.0.0 240.0.0.0 192.168.0.4 192.168.0.4 20
255.255.255.255 255.255.255.255 192.168.0.4 192.168.0.4 1
Passerelle par défaut : 192.168.0.1
 
I know that this MAC address is really strange, when I do a probe of the MAC address in Linux it give me that: FF:FF:FF:FF:FF:FF
 
Worst of all, why is it working in Windows and doesn't in Linux? The TCP/IP protocol is the same, right?
 
 
Mickael

Hi!
 
I found the answer: the MAC address is the broadcast, you can't use it so you have to change it executing this commandÇ
 
ifconfig eth0 hw ether AA:FF:EE:00:00:00 (or whatever address EXCEPT FF:FF:FF:FF:FF:FF). Linus give the broadcast by default.
 
Thanks!
 
Mickael

Sorry I saw this so late.
 
You asked a couple of questions:
 
* The HWare address also known as the MAC address is the physical ethernet address of the adapter in your computer. As you know, the ip address you are using 192.168.0.5 is not the same - obviously.
 
* The translation of MAC <-> IP is done by a facility known as ARP - Address Resolution Protocal. This allows ethernet packets (which really "hold" the TCP/IP packets) to be sent to the correct place. Without getting into too much detail, the address FF:FF:FF:FF:FF:FF is called the "broadcast address" and is NOT a legal node address.
 
* This explains why when you use /sbin/ifconfig hw ether ... to force the MAC address to be something other than FF:FF... your system works. (By the way, Windows does have a facility to create a dummy MAC address if a probe is not successful in getting the real one.) If you open a command window in Windows and issue:
 
arp -a
 
you will see the translation of MAC <-> IP there. It might be interesting if you would post what you see there.
 
* Ping is a different kind of packet or message on the network. It uses a protocol ICMP and does not have all the connection handshaking that TCP/IP has. When you attempted to access the web you use TCP/IP for http services (port 80). The TCP/IP connection is much more complex than ICMP. ICMP is like throwing a stone in a pond and hoping it bounces off something.
 
You will find a few things useful on Linux. Many times you can get a lot of information from the "man" pages. Open a terminal window and type
 
man arp
 
for instance. You will get a detailed explaination of arp (for instance). Also the "info" command can be useful.
 
And, do not forget the search engines. Do a google search on TCP/IP and you can get a huge list of links to the protocol (for example).
 
When you feel more confident, you should put your "ifconfig hw ether" into your system startup script. That way you will always start Linux with your network connection working.
 
Hope this has been useful.
Bill

under Windows, can you use device manager (Start->Run->"devmgmt.msc" ),
find the SiS network adapter, pull up the properties (right click) and
report the version number of your driver?
 
according to this article, you need v1.16 or later
before the correct MAC address can be revealed by "ipconfig /all".
 
also, under Linux, when your network interface driver loads correctly
you will see something that looks like this in /var/log/messages (or via "dmesg" ):
 
[size:3][tt]sis900.c: v1.07.06 11/07/2000
eth0: SiS 900 PCI Fast Ethernet at 0xd000, IRQ 10, 00:00:e8:83:7f:a4.
eth0: SiS 900 Internal MII PHY transceiver found at address 1.
eth0: Using SiS 900 Internal MII PHY as default[/tt]
 
Note carefully the first 3 octets of the MAC address.
 
The MAC address is assigned by SiS (id 0x0000e8) and is unique for the example
network interface (nbr 0x837fa4). Besides the ethernet broadcast address,
there is a whole range of addresses reserved for ethernet multicast which
you should not assign to your network interface.
 
Instead of trying to reassign your interface's address, I think it would be best
to fix the driver problems so you will end up using the MAC address already
allocated for your interface by SiS.
 
http://www.sis.com/support/index.htm
 
what is the full identification string returned by "lspci -v" for the interface?
 
for Windows, the latest driver appears to be v1.18 and for Linux it's v1.08.
 
Compare your Windows network driver to the contents of the LAN driver archive from ECS.
 

HELP...
 
I have a similar problem, but I didn't install anything new.. All of a sudden my internet stops working on my older PC. The networking still works between my two PCs. The PC that stopped working is running Win 98 and I can't find anything hardware wise wrong with it. I tried Firefox by Mozilla, because some people told me that IE can get virus that screw it up. But that didn't work either.
 
Any ideas?
 
My stuff.
Windows 98 IP Configuration
 
Host Name . . . . . . . . . : compaq.wowway.com
DNS Servers . . . . . . . . : 64.233.222.2
64.233.222.7
Node Type . . . . . . . . . : Broadcast
NetBIOS Scope ID. . . . . . :
IP Routing Enabled. . . . . : No
WINS Proxy Enabled. . . . . : No
NetBIOS Resolution Uses DNS : Yes
 
0 Ethernet adapter :
 
Description . . . . . . . . : SiS NIC SISNIC
Physical Address. . . . . . : 00-D0-09-E8-46-9A
DHCP Enabled. . . . . . . . : No
IP Address. . . . . . . . . : 192.168.1.104
Subnet Mask . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . : 192.168.1.1
Primary WINS Server . . . . :
Secondary WINS Server . . . :
Lease Obtained. . . . . . . :
Lease Expires . . . . . . . :