VIA Cicada VT6122 Gigabit LAN and Debian

Anyone got that thing working? Can see the actual card in dmesg. . But i have no net. . Im comfused. . .

Linux Networking 361 This topic was started by ,


data/avatar/default/avatar18.webp

4 Posts
Location -
Joined 2006-06-11
Anyone got that thing working?
 
Can see the actual card in dmesg.. But i have no net..
 
Im comfused..

Participate on our website and join the conversation

You have already an account on our website? Use the link below to login.
Login
Create a new user account. Registration is free and takes only a few seconds.
Register
This topic is archived. New comments cannot be posted and votes cannot be cast.

Responses to this topic


data/avatar/default/avatar10.webp

2895 Posts
Location -
Joined 2002-08-30
Can you give us a little more information?
 
Is this Debian Woody, Sarge, or Sid?
 
Are you connected to the internet by broadband or DSL?
 
Did you have internet access during the installation process, when the apt repositories were set up?
 
When you type in ifconfig in a terminal window, as root user, do you get any eth0 output lines? You should see output something like;
 
eth0 Link encap:Ethernet HWaddr 00:14:2A:E9:8F:0C
inet addr:192.168.1.47 Bcast:255.255.255.255 Mask:255.255.255.0
inet6 addr: fe80::214:2aff:fee9:8f0c/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:1264 errors:0 dropped:0 overruns:0 frame:0
TX packets:1328 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:972422 (949.6 KiB) TX bytes:296788 (289.8 KiB)
Interrupt:17
 

data/avatar/default/avatar18.webp

4 Posts
Location -
Joined 2006-06-11
OP
I run Sarge 3.1 64
 
I can see the card in ifconfig but i don't get a IP for it..
 
I connect directly to the net via rj45. No DLS or similar.. Just standard ethernet..

data/avatar/default/avatar10.webp

2895 Posts
Location -
Joined 2002-08-30
Quote:I connect directly to the net via rj45. No DLS or similar.. Just standard ethernet..

Well, DSL connects via ethernet, as well. So, you are connected to broadband via ethernet (the connection is always active)?
The problem is one of two possible issues.

1. The incorrect module is loaded for the card, which is possible.

2. The system is not set up for auto DHCP.

If you are running the Gnome display manager, go to;

System-->Aministration-->Networking. Does this show the card to be active?

Click on the ethernet connection that shows, then "edit" to edit the connection. Click on the box to check of DHCP. Finish the process and see if you get an IP address. If not, try typing into a root console'

ifup eth0

Then see if it works. if not reboot the system and see if it comes up at boot.

data/avatar/default/avatar18.webp

4 Posts
Location -
Joined 2006-06-11
OP
I have a fixed IP..
 
No dsl.. fiber all the way to my socket..
 
No DHCP..
 
I'll check the other stuff later this week..

data/avatar/default/avatar10.webp

2895 Posts
Location -
Joined 2002-08-30
If you have a fixed IP address (static), then of course, you have to tell Debian what the values are. From the article How To Set Up A Linux Network, read the following information from the "At Home" portion of the document;
 

Quote:On Windows PCs, go toStart/Settings/Control Panels/Networking
and get into the TCP/IP properties for the NIC where you can enter an IP address for the PC, a subnet mask, and possibly a default gateway (if you have a broadband Internet connection). When you enter an IP address into the TCP/IP properties like this it's called a "static" IP address because it won't change unless you change it.
 
Then you can go to the Debian network utility and add the values, configuring the network as a static connection.
 

Quote:No dsl.. fiber all the way to my socket.. 
I'm not sure what you mean by this, but either you have DSL (where the ethernet cable runs from the system to a DSL modem), or if via broadband, the CAT5 cable runs to the modem, which is connected to your broadband cable.

data/avatar/default/avatar18.webp

4 Posts
Location -
Joined 2006-06-11
OP
I don't use any modems what so ever.
 
 

data/avatar/default/avatar10.webp

2895 Posts
Location -
Joined 2002-08-30
Ok, then this is as far as I can take this thread without you telling us how exactly you are connected to the Internet.
 
Understand that we can't speculate what is wrong without knowing your exact situtation.
 
The article I referenced covers most of the bases for the various situations and using Debian to connect at home, work or on a private network.
 
If you are connecting to a network from work, or say from a dorm room or appartment complex which has a building/system wide Internet connection using a fixed ISP address, then perhaps you should consult the IT/LAN administrator to discuss how to connect and if using other than a supported OS setup works. I can only speculate on your situation, but this just results in too little information and wasted posts on both ends.
 
Either way, let us know what progess that you make.